Resistor color code
Bands to ohms and ohms to bands for 3 to 6 band parts. Warns when the bands could be read from the other end, and tells you if the value is a real E24 or E96 part.
Colors in → value, tolerance, range
BenchOhm is a small set of calculators for people who build circuits: students on their first breadboard, Arduino tinkerers, guitar-pedal builders and repair techs. Each one gives the answer you need and then the part you should actually put in.
Quick answer for resistance: R = V ÷ I. To drop 5 V at 15 mA you need 5 ÷ 0.015 = 333.3 Ω; the nearest standard part is 330 Ω.
Resistance
333.3 Ω
Nearest E24 part 330 Ω · dissipates 75 mW · 0.25 W rating is enough.
Need power, or have watts instead of amps? Use the full Ohm's law calculator.
Bands to ohms and ohms to bands for 3 to 6 band parts. Warns when the bands could be read from the other end, and tells you if the value is a real E24 or E96 part.
Colors in → value, tolerance, range
Any two of volts, amps, ohms and watts give the other two. Under every answer: the resistor wattage to buy and the nearest standard value.
Two values in → all four + wattage
Total resistance of up to ten resistors, the current and heat in each branch, and the pair of standard parts that hits a value your kit lacks.
Resistor list in → total, branches, pairs
Resistors end to end: the total, the one current through them, the voltage and heat on each part, and which two kit values add up to the one you are missing.
Resistor list + supply in → total, drops, pairs
Most mistakes on the bench are unit mistakes: a 4.7k resistor typed as 4.7, or 20 mA typed as 20. Our calculators accept prefixes directly (4k7, 2.2M, 0R47), but when you work by hand, convert to base units first.
| Prefix | Name | Factor | Example |
|---|---|---|---|
| G | giga | 10⁹ | 1 GΩ = 1,000 MΩ |
| M | mega | 10⁶ | 2.2 MΩ = 2,200,000 Ω |
| k | kilo | 10³ | 4.7 kΩ = 4,700 Ω |
| — | base unit | 1 | 12 V, 0.5 A, 330 Ω |
| m | milli | 10⁻³ | 20 mA = 0.02 A |
| µ | micro | 10⁻⁶ | 100 µA = 0.0001 A |
| n | nano | 10⁻⁹ | 100 nF = 0.1 µF |
| p | pico | 10⁻¹² | 22 pF = 0.022 nF |
Resistor shorthand uses the prefix letter as the decimal point, so that a smudged dot cannot turn 4.7k into 47k: 4k7 = 4.7 kΩ, 2R2 = 2.2 Ω, 1M5 = 1.5 MΩ.
The handful of relationships behind almost every resistor decision. Each one links to the calculator that does it for you, with units and rounding handled.
| Formula | Use it when | Calculator |
|---|---|---|
| I = V ÷ R | you know the voltage and the resistor and want the current | Ohm's law |
| P = V² ÷ R | you need to know how hot a resistor gets and which wattage to buy | Ohm's law |
| R = (Vs − Vf) ÷ I | sizing the series resistor for an LED | Ohm's law (worked example) |
| 1/Rt = Σ 1/R | resistors share both ends, or you want to lower a value | Parallel |
| R = digits × 10ⁿ | reading the bands on a through-hole resistor | Color code |
A typical starter kit holds 30 to 60 values from the E12 series, ten or twenty of each. Three habits make it go further:
Before a resistor goes on the board, read its bands and then confirm with a meter; resistors that have been loose in a drawer for years are often from a different bag than the label says.
Every calculator here runs on one small math file that is shared by the page and by our test suite. Before a calculator goes live it must pass hand-worked examples, property checks (for example: a parallel total is always below the smallest resistor, and an encoded color code always decodes back to the same value), and a comparison against at least two independent references on three inputs. Color code data follows IEC 60062 and standard values follow the IEC 60063 E-series. The details, and the list of comparisons, are on the methodology page. If a number looks wrong, tell us: every report is reproduced, and a confirmed error becomes a new test.
Next up are the tools most requested by builders: series resistors, the voltage divider, the LED resistor with forward-voltage presets, standard resistor values, RC time constants and the 555 timer in astable and monostable mode. They will appear here as they pass the same checks.
The site is written for the hobby and learning bench: low-voltage DC circuits, from a coin cell up to a 24 V supply. That covers breadboards, microcontroller projects, LED work, sensors, audio and repair of small electronics. Household wiring, breaker sizing and anything on the mains is a different job with different rules, and it belongs with a licensed electrician.